0 of 23 questions completed Questions:
You have already completed the quiz before. Hence you can not start it again.
Quiz is loading...
You must sign in or sign up to start the quiz.
You have to finish following quiz, to start this quiz:
0 of 23 questions answered correctly
Your time:
Time has elapsed
You have reached 0 of 0 points, (0) Which command can be issued on a router to verify that automatic summarization is enabled?
Which address best summarizes the IPv6 addresses 2001:DB8:ACAD::/48, 2001:DB8:9001::/48, and 2001:DB8:8752::/49?
In which IOS CLI mode must a network administrator issue the maximum-paths command to configure load balancing in EIGRP?
Two routers, R1 and R2, have established an EIGRP neighbor relationship, but there is still a connectivity problem. Which issue could be causing this problem?
In which scenario will the use of EIGRP automatic summarization cause inconsistent routing in a network?
What action should be taken to solve this problem?
Two routers, R1 and R2, share a 64 kb/s link. An administrator wants to limit the bandwidth used by EIGRP between these two routers to 48 kb/s. Which command is used on both routers to configure the new bandwidth setting?
Which three statements are advantages of using automatic summarization? (Choose three.)
What is a characteristic of manual route summarization?
Fill in the blank. Do not use abbreviations.
Fill in the blank. Do not use abbreviations. What is the command that should be issued on a router to verify that EIGRP adjacencies were formed? (show ip eigrp neighbor, SHOW IP EIGRP NEIGHBOR) Launch PT Hide and Save PT R1 and R2 could not establish an EIGRP adjacency. What is the problem?
CCNA 3 Scaling Networks Chapter 8 v5.0 Exam
Quiz-summary
Information
CCNA 3 Scaling Networks Chapter 8 v5.0 Exam
Results
Average score
Your score
Categories
Pos.
Name
Entered on
Points
Result
Table is loading
No data available
1. Question
2 points
2. Question
2 points
3. Question
2 points
Refer to the exhibit. Router R3 is receiving multiple routes through the EIGRP routing protocol. Which statement is true about the implementation of summarization in this network?
4. Question
2 points
Refer to the exhibit. Considering that R2, R3, and R4 are correctly configured, why did R1 not establish an adjacency with R2, R3, and R4?
5. Question
2 points
6. Question
2 points
7. Question
2 points
Refer to the exhibit. Remote users are experiencing connectivity problems when attempting to reach hosts in the 172.21.100.0 /24 network. Using the output in the exhibit, what is the most likely cause of the connectivity problem?
8. Question
2 points
9. Question
2 points
Refer to the exhibit. Routers R1 and R2 are directly connected via their serial interfaces and are both running the EIGRP routing protocol. R1 and R2 can ping the directly connected serial interface of their neighbor, but they cannot form an EIGRP neighbor adjacency.
10. Question
2 points
Refer to the exhibit. Which statement accurately reflects the configuration of routing on the HQ router?
11. Question
2 points
Refer to the exhibit. Which statement is supported by the output?
12. Question
2 points
Refer to the exhibit. Which two routes will be advertised to the router ISP if autosummarization is disabled? (Choose two.)
13. Question
2 points
Refer to the exhibit. A network administrator has configured EIGRP authentication between routers R1 and R2. After the routing tables are reviewed, it is noted that neither router is receiving EIGRP updates. What is a possible cause for this failure?
14. Question
2 points
15. Question
3 points
16. Question
2 points
Refer to the exhibit. After the configuration shown is applied on router R1, the exhibited status message is displayed. Router R1 is unable to form a neighbor relationship with R2 on the serial 0/1/0 interface. What is the most likely cause of this problem?
17. Question
2 points
18. Question
3 points
19. Question
2 points
Refer to the exhibit. A network administrator has issued the shown commands. The EIGRP routing domain has completely converged and a network administrator is planning on configuring EIGRP authentication throughout the complete network. On which two interfaces should EIGRP authentication be configured between R2 and R3? (Choose two.)
20. Question
3 points
21. Question
2 points
Open the PT Activity. Perform the tasks in the activity instructions and then answer the question.
22. Question
2 points
Refer to the exhibit. A network administrator has attempted to implement a default route from R1 to the ISP and propagate the default route to EIGRP neighbors. Remote connectivity from the EIGRP neighbor routers to the ISP connected to R1 is failing. Based on the output from the exhibit, what is the most likely cause of the problem?
23. Question
2 points
Refer to the exhibit. All networks are active in the same EIGRP routing domain. When the auto-summary command is issued on R3, which two summary networks will be advertised to the neighbors? (Choose two.)
CCNA 3 Scaling Networks Chapter 8 v5.0 Exam
CCNA 3 Scaling Networks Chapter 8 v5.0 Exam
CCNA 3 Scaling Networks Chapter 8 v5.0 Exam